Bleed, crop marks and print checks
Send your printer a check report: what it shows
Short answer: the report is a short PDF that shows what the Print-Ready check found in your file and with which settings. Send it along with your file so your printer can see what has already been looked at, and which points you want them to confirm. It is a record, not an approval.
What is in it
| Section | What it tells the reader |
|---|---|
| Header | File name, date checked, and a status: "Checked, PDF not created yet" or "PDF created" |
| File facts | Pages, file size, trim size, size with bleed, PDF page size, marks, Print for, edge detection, paper standard, total ink limit, Less ink setting. For a JPG or PNG, also the image resolution used |
| Picture | The first page with its bleed and crop marks in place, with numbered markers pointing to what was found there. It is a preview |
| Three counts | Passed, will be fixed (or fixed), and to look at |
| The list | Each item under Will be fixed, Change in your design and Worth a look, with what it means and which pages. Then Passed and Not checked. The numbers match the list on screen |
| Footer | A note that the check ran in the browser, and that an automatic check cannot see everything |
Where each item stands is written in words as well as color, so it can still be read on a black-and-white copy. The page size follows your unit setting: A4 for millimeters, US Letter for inches.
When it helps
- Your printer asked what you checked. The report answers that with the actual numbers.
- You are handing off someone else's file. A designer can send it to a client to show what still has to change.
- A file was rejected. Compare their message with the list to see which item it matches, then ask about the rest. See common rejection reasons.
- You want to raise a question. "Line 12 says Special inks: is that what you expect?" is quicker than describing it.
How to read "will be fixed" and "fixed"
This is the part that is easiest to misread. Until you create the file, the report says what will be fixed. After you create it, those rows say Fixed for a file made from the same settings. Change a setting afterward and the status goes back. So make the report last, once the settings are final.
Even then, "Fixed" describes what the settings do. The check does not run again on the new file. If you want a report on the finished PDF itself, drop it into Print-Ready as a new file. To read its ink, open it in the Ink Checker. Converted colors are capped at the ink limit you pick, but the created file is not measured again, so it is worth confirming.
What it does not say
- That the file will be accepted. Only your printer can tell you that.
- That the file is PDF/X. It is not validated as PDF/X.
- Anything about barcodes, QR codes or die lines. They appear under Not checked.
- How the colors will look on your paper. A picture in the report is not a proof.
- What other pages look like. The picture shows the first page only, and other pages appear only in the list.
A note to send with it
You can copy this:
"Attached is my print file and a check report. It's from an automatic check, so please treat it as background and let me know if your own check finds anything. I'd like you to confirm: ____."
To make one, drop your file on the Print-Ready page and click Report → Print-ready report (PDF). It saves as your file name followed by _print-check.pdf.
Frequently asked questions
Is the report a certificate that the file is fine to print?
No. It records what an automatic check found with the settings you chose. Your printer has its own requirements and their own check, and the report does not replace either.
Is my file uploaded to make the report?
No. The report is made in your browser, and you can download it before you create the PDF.
Do I need an account to download the report?
No. You don't need an account to check a file, preview it, download the report or download the print-ready PDF. Signing in (free) keeps your files for 7 days.
Does the report measure the finished PDF?
Not unless you check that file. A report downloaded after creating the PDF marks the fixes as done with your settings, but it does not re-measure the new file. To check it, drop the created PDF in again, or open it in the Ink Checker for ink.