Bleed, crop marks and print checks
My printer rejected my PDF: common reasons and how to fix each
Short answer: printers often send a PDF back because of missing bleed, low-resolution images, missing fonts, RGB colors, too much ink or the wrong size. Find your printer's wording below, then follow the fix. Some problems can be fixed in the finished PDF. Others have to go back to the design file.
What the message means and what to do
| The printer says | It usually means | Fix |
|---|---|---|
| "No bleed" or "needs 3 mm bleed" | Artwork stops at the cut. | Add bleed to the PDF |
| "Add crop marks" or "remove crop marks" | The marks do not match how they work. | Turn crop marks on or off |
| "No trim box" | The file does not say where to cut. | Set the page boxes |
| "Wrong size" | The finished size is not what was ordered. | Set the finished size if the design already fits. This sets the cut and does not scale the design, so if the page is smaller than the size ordered, go back to the design. |
| "File is RGB" or "CMYK only" | Colors are set for screens. | Convert to CMYK |
| "Too much ink" or "over 300%" | Dark areas go over their ink limit. | Reduce the ink, then confirm in the Ink Checker |
| "Low-resolution images" | Photos do not have enough pixels at their printed size. | In the design: use a larger original or print smaller |
| "Fonts not embedded" | The font is not in the PDF. | In the design: export again with fonts embedded |
| "Text too close to the trim" | Text sits inside their safe margin. | In the design: move the text inward |
| "Lines too thin" | Lines may break up on press. | In the design: make them thicker |
| "Registration color used" | Artwork prints in every ink. | In the design: change the color |
| "Page count must be a multiple of 4" | The booklet cannot fold from whole sheets. | In the design: add or remove pages |
| "Unexpected spot colors" | The file asks for extra inks. | Reported only. Change them in the design if the job does not need them. |
| "Flatten transparency" | Their workflow does not take live transparency. | Not done here. Ask how they want it and export from your design tool. |
| "File is locked" | The PDF has a password. | Export again without one. Encrypted PDFs cannot be used in Print-Ready either. |
| "Must be PDF/X" | They require a specific PDF standard. | Print-Ready does not validate PDF/X, and it rewrites the file, so a PDF/X export is not the same file afterward. Ask whether they accept the Print-Ready file, or make the changes in your design and export PDF/X last. |
| Barcode or die line problems | Their setup or size is not what the job needs. | Not checked here. Ask them for the specification. |
Fix things in this order
When a file has several problems, start with the design and finish with the PDF. A new export replaces the finished PDF, so anything you did to the old one has to be done again. If your printer requires PDF/X, see the table above first.
- Design changes first: images, fonts, text position, thin lines, registration color and page count. Then export again.
- Then check the new export. Drop it on the Print-Ready page to see what is still listed. The check runs in your browser, and no account is needed.
- Then fix the finished PDF: set the finished size, bleed and crop marks, and create the file. Colors are converted to CMYK in the same step, and the ink is reduced unless you turn Less ink off.
- Check your printer's points again. Look at the preview, and read the ink in the Ink Checker if ink was the problem.
What to ask your printer
A short question can save another round. You can copy these:
- "Which requirement did the file fail, and on which page?"
- "What finished size and bleed do you need? Do you want crop marks?"
- "What is your total ink limit, and which paper standard should I use?"
- "Do you need PDF/X? If so, which version?"
- "Is this level of image resolution acceptable for this job?"
If you resend, name the file so it cannot be confused with the old one, such as adding v2.
Frequently asked questions
Can I fix a rejected PDF without the original design file?
Often, yes, for bleed, crop marks, page boxes, RGB colors and too much ink (then confirm the ink in the Ink Checker). Bleed can be added to a finished PDF, but check the result, because bleed made from the edge (Smart extend or a mirror) does not suit every design. Low-resolution images, missing fonts, text too close to the cut, very thin lines and registration color need a change in the design file.
My printer's message is vague. What should I do?
Ask which requirement failed and on which page. Also ask for their file requirements, such as bleed size, crop marks, ink limit and PDF format.
Should I send my printer the check report?
You can, if it helps the conversation. It lists what was found. It is not a certificate, and your printer will still run their own check.
My printer wants PDF/X. Can Print-Ready do that?
No. The file is not validated as PDF/X, and Print-Ready changes the file. If your printer requires PDF/X, ask whether this file is acceptable, or fix the issues in your design and export PDF/X from there as the final step.