Bleed, crop marks and print checks
Bleed size: 3 mm, 1/8 inch or 5 mm?
Short answer: use the number your printer gives you. Without one, 3 mm is a common value in Europe, the UK and Asia, and 1/8 inch (3.175 mm) in the US and Canada. These are habits, not a universal standard, and some printers ask for 5 mm or more.
The sizes side by side
Bleed is added to each side, so the page grows by twice the bleed in each direction. Here is what that does to the PDF page, with no crop marks:
| Bleed | In the other unit | Commonly asked for in | A4 (210 x 297 mm) becomes | US Letter (8.5 x 11 in) becomes |
|---|---|---|---|---|
| 3 mm | 0.118 in | Europe, UK, Asia | 216 x 303 mm | 221.9 x 285.4 mm |
| 1/8 in | 3.175 mm | US, Canada | 216.35 x 303.35 mm | 8.75 x 11.25 in |
| 5 mm | 0.197 in | Some printers and jobs | 220 x 307 mm | 225.9 x 289.4 mm |
The regions are this tool's starting labels, not survey results. The gap between 3 mm and 1/8 inch is 0.175 mm a side. It rarely matters on the press. It can matter at an online upload step that compares your page with an exact size.
Why a printer may ask for something else
The number depends on the printer's equipment and on the job, so no article can give you the right value for yours. You may be asked for a larger bleed on some large pieces or bound work, or for an exact page size on a service's template. Do not assume. A template from your printer overrides any general rule, including the values on this page.
What to ask your printer
You can copy these questions:
- How much bleed do you need on each side, in mm or inches?
- Should the PDF page be the finished size plus bleed, or do you want crop marks on a larger page?
- Do you check for an exact page size when the file is uploaded? If so, what size?
- Do you have a template for this product?
- Does every edge need bleed, or only those where artwork reaches the edge?
Setting it in Print-Ready
Bleed in Print-Ready offers 3 mm, 1/8 in, 5 mm, No bleed and Custom. A custom value can be anything from 0 to 5 mm. The tool picks mm or inches from your file's size or your browser's region, and starts from the usual value in that unit: 3 mm or 1/8 in. So check it against your printer's number rather than leaving it as is. With bleed, beside the finished size, shows the resulting size. The PDF page is larger than that when crop marks are on, which is the starting choice for Print shop.
The 5 mm ceiling is deliberate. Wide bleed cannot be made well from artwork that stops at the cut, because the made strip (mirrored or extended with Smart extend) has to reach farther into the artwork. If your printer wants more than 5 mm, extend the artwork in your design file and export again. That is also the better route for a large bleed under the limit, if you have the design. See when mirrored bleed is fine and how to add bleed to a PDF.
Frequently asked questions
Is 3 mm the same as 1/8 inch?
Nearly. 1/8 inch is 3.175 mm, so the two differ by 0.175 mm per side. Many printers treat them as the same, but an upload system that checks exact page sizes may not, so follow the number on your printer's list.
Is more bleed safer?
Not automatically. Extra bleed gets cut away, but a system that expects an exact page size may flag the file. When bleed has to be built from a finished PDF, a wider strip also shows more made-up content, mirrored or extended.
What if my printer does not state a bleed size?
Ask. If you cannot get an answer before your deadline, the usual value for your region is a common choice, but it is a guess, not their requirement.