Bleed, crop marks and print checks

My printer asked for 3 mm bleed: what to do with a finished PDF

Updated · 3 min read

Short answer: your printer wants any artwork that touches the edge of the page to continue 3 mm past the cut line, on each side where it touches. For an A4 finished size, the artwork then measures 216 x 303 mm, with the cut still at 210 x 297 mm. You do not shrink the design or add a border. To add it to a finished PDF, drop the file on Print-Ready, set the finished size and bleed, and create the PDF.

Why they asked

Cutting moves a little from sheet to sheet. If the color ends exactly on the cut line, a small shift leaves a thin line of bare paper along the edge. With 3 mm of extra artwork outside the line, a small shift only cuts into the extra. That extra is thrown away.

A common misunderstanding is to treat bleed like a margin. A margin sits inside the page and keeps text away from the cut, which is a separate question covered in the safe area guide.

Does your PDF already have it?

Open the file in a PDF viewer and find the page size. Many viewers show it under the document properties. Then compare it with the size you ordered. This example uses A4 and 3 mm:

Page size in the PDFUsually meansWhat to do
210 x 297 mm, same as the orderNo bleed. The artwork stops at the cut.Add bleed
216 x 303 mm, 6 mm more each wayBleed is probably included, but the file may not mark the cut.Confirm the finished size is set to 210 x 297 mm
Much larger, with crop marks visibleExported with marks and probably with bleed.Zoom in on a corner: does the color run past the marks' line?
Any size, with white at all edgesNothing runs off the page, so bleed has nothing to do.Tell the printer the edges are white

A larger page may just have empty space around the design, so zoom in to the corners to see that the color continues by the full 3 mm. An edge with less is treated as having no bleed, and Print-Ready makes it instead (a mirror by default; picture edges can use Smart extend instead).

How to add it

If you can open the design: turn on the bleed option in your design tool, if it has one, stretch the background past the page edge, and export again. This is the more accurate route, because the artwork itself continues.

If you only have the PDF: drop it on Print-Ready. In your browser, it reports which edges have no bleed, for example No bleed on any edge. It then shows the file with bleed added before anything is uploaded (the preview draws the bleed for the first 12 pages that need it). Pay attention to three settings:

  • Print for. The starting choice, Print shop, turns Crop marks on and makes the page 248.1 x 335.1 mm for A4. If your printer wants bleed only, choose Online printing service. The page is then 216 x 303 mm.
  • Cut size. If your page is already 216 x 303 mm but the file does not mark the cut, type 210 x 297 mm. Otherwise another 3 mm goes on top.
  • Bleed. Pick 3 mm. It is the starting value in mm; if the tool opens in inches, it starts at 1/8 in, so change it.

The steps and limits are in adding bleed without the design file.

What to send back

You can copy and adjust this short message:

"Attached is the PDF with 3 mm bleed. Finished size is 210 x 297 mm, and the PDF page is 216 x 303 mm. Do you also need crop marks on the page? The bleed was made from the artwork at the edges, since I only had the exported PDF. Please let me know if that is a problem."

Check the page size in the message against the file you made. With crop marks on, the page is larger than the finished size plus bleed. A check here does not mean the printer will accept the file. They have their own check and the final word.

Frequently asked questions

Should I shrink my design to make room for bleed?

No. The finished size stays the same and the page gets larger around it. Shrinking the artwork would leave a white edge after cutting.

Does a design with a white background need bleed?

Usually not, because nothing runs off the page. The file still needs to say where the cut is. If only one edge has color, only that edge needs bleed.

Is bleed the same as a margin?

No. Bleed is outside the cut and gets trimmed off. A margin, or safe area, is inside the cut and keeps text away from the edge.