Bleed, crop marks and print checks
Set the finished size of a PDF for print: custom size and common sizes
Short answer: the finished size, also called the trim size, is the size of the piece after cutting. Setting it on a PDF tells the printer where the cut goes. It does not resize your artwork. In Print-Ready, it is Cut size in the Settings tab: keep it as in the file, pick a common size, or type your own.
Finished size, size with bleed, PDF page
These three are easily mixed up, and a printer may mean any of them when they say "page size". Here are examples with the usual bleed in that unit. With bleed is also the PDF page when marks are off. The starting choice, Print shop, has marks on:
| Finished | With bleed | PDF page with crop marks |
|---|---|---|
| A4, 210 x 297 mm | 216 x 303 mm | 248.1 x 335.1 mm |
| A5, 148 x 210 mm | 154 x 216 mm | 186.1 x 248.1 mm |
| US Letter, 8.5 x 11 in | 8.75 x 11.25 in | 10 x 12.5 in |
| Postcard, 4 x 6 in | 4.25 x 6.25 in | 5.5 x 7.5 in |
| Business card, 90 x 54 mm | 96 x 60 mm | 128.1 x 92.1 mm |
The bleed here is 3 mm or 1/8 in per side, and crop marks add 19.05 mm (3/4 in) per side to the finished size. Your printer's bleed may differ.
When you need to set it
- Your page already includes bleed, but the file does not mark the cut. A 216 x 303 mm page would otherwise be read as the finished size, and more bleed would go on top. Type 210 x 297 mm, and the artwork around it counts as bleed.
- Your page has marks or empty space around the design, and no trim box. The same applies. Anything beyond the bleed box is cut away from the new page, including old marks there.
- The file's trim box is wrong. Typing the size replaces it.
If the PDF page already is the finished size, or the file has a correct trim box, leave it on As in the file.
What setting it does and does not do
| It does | It does not |
|---|---|
| Set the trim box and bleed box for the new page | Scale the artwork up or down |
| Place the cut in the center of the page | Let you position the cut anywhere else |
| Treat what is on the page around the cut as bleed | Create artwork beyond the page, other than the mirrored bleed |
| Apply the same size to all pages | Accept a size bigger than a page |
The centering matters most. If your design sits off-center on the page, the cut will land in the wrong place. Before you continue, look at the cut line in the preview, and in that case fix the position in your design and export again.
Setting a smaller size on a design made for a larger one is a crop, not a resize. Anything outside the new cut and bleed is lost from the new file, and text near the old edge may be cut. The check runs again on the new size, so it reports text too close to the cut for you.
Common sizes in the list
The size list includes A3 to A6, US Letter, Legal and Tabloid, three business cards (90 x 54 mm, 85 x 55 mm, 3.5 x 2 in), a 4 x 6 in postcard, a 5 x 7 in card and a 210 mm square. A size from the list turns to match your first page's orientation. If your pages mix portrait and landscape, a single finished size may not fit all of them. Choose Custom size to type any other. The swap button exchanges width and height.
Your printer's order form is the reference for the size. For products with a template, such as a book cover, follow the template, since its page size may not be the finished size of a single piece. The tool cannot tell you which size you ordered, so compare Cut size and With bleed against your order before you create the PDF. For pages that differ on purpose, see different page sizes in one PDF.
Frequently asked questions
Can I make an A4 PDF print as A5 this way?
Not by shrinking it. Setting A5 on an A4 page keeps the artwork at its size and cuts out the center A5 area. To reduce the design, change it in your design tool and export again.
Can I set a finished size bigger than the page?
No. The tool shows an error, because the finished size has to fit inside each page.
Can different pages have different finished sizes?
A finished size you set applies to all pages. If your pages are meant to differ, keep As in the file, which reads each page separately, and check that each page marks its own cut.
My design is not centered on the page. What can I do?
Center it in your design tool and export again. A custom finished size is always placed in the middle of the page.