Bleed, crop marks and print checks
Business card PDF: bleed, crop marks and safe area
Short answer: a business card PDF usually needs artwork running about 3 mm or 1/8 inch past the cut if any color touches the edge, text kept a few millimeters inside the cut, and crop marks only if your printer wants them. These numbers are common values rather than a standard, so your printer's instructions come first.
Page sizes for common cards
Bleed is the extra artwork past the cut. Crop marks are the short lines that show where to cut. Print-Ready has these three cards as presets under Cut size. Here is the page you should expect with each setup:
| Finished card | Bleed | Page with bleed, no marks | Page with crop marks |
|---|---|---|---|
| 90 × 54 mm | 3 mm | 96 × 60 mm | 128.1 × 92.1 mm |
| 85 × 55 mm | 3 mm | 91 × 61 mm | 123.1 × 93.1 mm |
| 3.5 × 2 in | 1/8 in | 3.75 × 2.25 in | 5 × 3.5 in |
The last column uses Print-Ready's page, which is 19.05 mm (3/4 in) larger than the card on each side when marks are on. Other tools may use a different margin. A preset sets the cut. It does not resize your design, so the file must already be made for that card size.
The safe area is tighter than it sounds
The safe area is the zone near the cut where text can get trimmed or just look crooked. The check's default is 3 mm. On a 54 mm tall card that leaves 48 mm of height for text, and name, title and contact lines fill that quickly. If your layout feels cramped, reduce the content instead of moving it toward the edge. Print-Ready reports live text that is too close to the cut, but it does not move it. Text turned into outlines, logos and other graphics near the edge are not measured, so look at those yourself.
Thin borders are a similar trap. A frame running parallel to the edge makes any small cutting shift easy to see, because one side ends up visibly wider than the other. If you want a border, ask your printer how close to the cut they are comfortable with. The check does not look for this.
Small black text
Contact details are often 6 to 9 pt. If black text is built from cyan, magenta, yellow and black, the four inks have to line up on every letter, and a slight shift makes small text look soft. Print-Ready flags black text in four inks below 12 pt by default. When you create the file, text that looks black and meets our black-text rule becomes black ink only. Some deliberate rich blacks are left as they are, and you can switch this off.
White text on a dark card has the opposite problem: it is made by the inks around it, so fine strokes can fill in. Use a slightly heavier weight for small white text and ask for a proof if you can. The check does not measure the strokes of white text.
Stroked lines thinner than 0.25 pt, the default limit, are reported because they can break up or disappear.
Dark card backgrounds
Navy and near-black cards can carry a lot of ink. In our business card example (tested 16 October 2026, GRACoL 2013, 300% ink limit), the darkest point was 256% with a plain CMYK conversion and 236% with Less ink at Medium with Deeper blacks. Your file will differ. Less ink is on by default in Print-Ready; open the finished PDF in the Ink Checker to confirm the ink.
Questions for your printer
- What finished size and bleed do you want?
- Crop marks, or no marks?
- Should front and back be two pages of one PDF, or two files?
- How small can white text be on a dark background on this paper?
- If the card has rounded corners or a special finish, how should that be supplied?
Rounded corners, foil and spot gloss usually need a separate setup from your printer. Print-Ready does not create or check die lines, and it does not check barcodes or QR codes.
Frequently asked questions
What size should a business card PDF be with bleed?
The finished size plus the bleed on each side. A 90 × 54 mm card with 3 mm bleed has a 96 × 60 mm page. Common sizes and bleed values vary by country and printer, so ask yours.
Does a business card need crop marks?
It depends on the printer. Many online printing services want bleed and no marks; many print shops want marks. Ask, or follow the service's instructions.
Should the two sides be one PDF?
Often yes, as a two-page PDF with both pages the same size, but ask your printer how they want the front and back supplied.
Does the check test my QR code?
No. Barcodes and QR codes are not checked. Scan a printed test or a proof, and ask your printer if the code is small.