Bleed, crop marks and print checks
Why a white line shows after cutting, and how to prevent it
Short answer: the white line is usually bare paper. The artwork stopped at the cut line, or a little short of it, and the cut landed slightly outside. Artwork that runs past the cut (bleed) prevents it, and any gap between the artwork and the cut has to be closed too.
Find out what you are looking at
Where the line appears tells you most of what you need to know:
| What you see | Likely cause | What to do |
|---|---|---|
| Thin white line on one or more cut edges, on most copies | No bleed, or artwork that stops short of the cut | Check the file, then add bleed |
| Line is wider on some copies, or moves from side to side | The cut is shifting within a normal range and the file has little or no bleed | More bleed in the file. Ask the printer what range to expect |
| White along a fold, not a cut | Often cracking: the ink or paper splits at the fold, more likely with heavy ink or against the paper grain. A fold that lands slightly off the line can also show white | Ask the printer about scoring, paper or fold direction. Bleed does not stop cracking |
| Fine lines on screen that change when you zoom | Often a display effect in the PDF viewer | Zoom in and check whether they stay. A printed proof settles it |
| A border near the edge looks uneven | Not a bleed fault: a small shift shows clearly against a thin border | Make the border wider in the design, or remove it |
The case that looks fine on screen
A file can have a background that seems to reach the edge and still print a white line. This happens when the background was placed a fraction short of the page, for example 0.75 mm. In a viewer, that gap is white against a white surround, so it is easy to miss. After cutting, it shows as a line, and adding bleed outside the cut does nothing for it unless the gap is closed as well.
To check by eye, zoom in to several hundred percent on each edge and each corner. Look for a pale strip between the color and the end of the page.
How the check handles a gap
Print-Ready measures this from a rendering of each page in your browser, and the list says, for example, Artwork stops 0.75 mm short of the cut. The setting behind it is Edge detection, under Advanced in the Settings tab. It is 1 mm by default and can go up to 3 mm:
- Artwork that stops within that distance counts as reaching the cut. The gap and the bleed are both filled from just inside the artwork: by default, edges are mirrored. For picture edges you can set Picture edges to Smart extend (continued from the picture) or Leave as they are.
- Artwork that stops farther away is treated as a deliberate white margin and left alone. If an edge was missed, try a larger value.
- Set it to 0 to look only at the cut itself.
Two limits to keep in mind. The check goes by what shows, so a tint lighter than roughly 3% can read as blank paper, and no bleed is built on that edge. And a cropped picture's hidden part stays hidden, so that edge is mirrored. Look at the result in the preview.
Preventing it next time
- In the design, run backgrounds and pictures past the page edge rather than to it.
- Export with bleed if your design tool offers it, and with the amount your printer asks for. Common values are in bleed size: 3 mm, 1/8 inch or 5 mm.
- Make sure the file says where the cut is. Bleed in a file with no trim box leaves the printer guessing where to cut. See trim box and bleed box.
- If all you have is the PDF, add bleed to it before you send it.
Bleed reduces the risk from normal cutting shifts. It does not cover a job that was cut badly out of position, so if the line is large or uneven, show the printer a sample.
Frequently asked questions
Why can't I see the gap on screen?
A gap under a millimeter is easy to miss against a white page background in a PDF viewer. Zoom in a long way on the edge, or use a check that measures it.
Is 1 mm of bleed enough?
It depends on the printer. Common requests are 3 mm or 1/8 inch, so ask yours rather than cutting it close.
Can the printer add the missing bleed for me?
Some can, and they may charge for it or send the file back. Ask them. The file you send should not depend on it.
Why is there a white line only along one edge?
Usually only that edge is short, or the cut moved that way on that job. Check that edge in the file first, since the other edges may have enough bleed.